[Simh] simh and RSTS/E - problems with getting additional terminal interfaces to work
Johnny Billquist
bqt at softjar.se
Mon Dec 9 05:29:49 EST 2019
In RSTS/E, you have DZ11 lines, but they are configured for a CSR of
160100 and 160110, and vectors are 400 and 410. I bet that does not
match what simh thinks...
Johnny
On 2019-12-09 11:25, Trevor Warwick wrote:
>
> I'm using "PDP-11 simulator V4.0-0 Current", and getting the same
> results on Win10 and Linux.
>
> I'm booting the full RSTS V7.0-07 disk, built by by Chuck Cranor. This
> boots fine, and I can log in on the simulated console. However, I can't
> persuade it to recognise any additional terminals. If I use:
>
> set dli enable
> set dli lines=8
> attach dli 10001
>
> Then I get a telnet server appearing on port 10001, which prints
> "Connected to the PDP-11 simulator DLI device, line 0" when I boot the
> RSTS system disk. However, there's no response to any input once RSTS is
> up and running. I've also tried using a DZ11
>
> set dz lines=8
> attach dz 10002
>
> and in that case I don't even get the "Connected...." line from simh.
> RSTS can apparently see the hardware though:
>
> RSTS V7.0-07 llama (DL0)
>
>
> Option: HA
>
> HARDWR suboption? LI
>
> Name Address Vector Comments
> TT: 177560 060
> RK: 177400 220 RK05F units: none
> RL: 174400 160 Units: 0(RL01) 1(RL01) 2(RL01) 3(RL01)
> RM: 177440 210 Units: 0(RK06) 1(RK06) 2(RK06) 3(RK06) 4(RK06)
> 5(RK06) 6(RK06) 7(RK06)
> RR: 176700 254 BAE=+050, Units: 0(RM03) 1(RM03) 2(RM03)
> 3(RM03) 4(RM03) 5(RM03) 6(RM03) 7(RM03)
> TM: 172520 224
> PR0: 177550 070
> PP0: 177554 074
> LP0: 177514 200
> RX0: 177170 264
> KL0: 176500 300
> KL1: 176510 310
> KL2: 176520 320
> KL3: 176530 330
> KL4: 176540 340
> KL5: 176550 350
> KL6: 176560 360
> KL7: 176570 370
> DZ0: 160100 400
> DZ1: 160110 410
>
> KW11L 177546 100
> SR 177570
> DR 177570
>
> Hertz = 60.
>
> Other: FPU, SL, 22-Bit Addressing, Cache w/address, System ID = 4660
>
> If I boot an RSX-11M disk, then additional terminal interfaces seem to
> work fine, so the problem seems specific to RSTS. I saw references in
> the list archive to other pre-built systems on www.rsts.org
> <http://www.rsts.org> but that doesn't seem to be available at the
> moment, so I can't try another build right now.
>
> Any clues on what I'm missing ?
>
> Thanks,
> Trevor
>
>
>
> _______________________________________________
> Simh mailing list
> Simh at trailing-edge.com
> http://mailman.trailing-edge.com/mailman/listinfo/simh
>
--
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt at softjar.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
More information about the Simh
mailing list