<div dir="ltr"><br><div>I'm using "PDP-11 simulator V4.0-0 Current", and getting the same results on Win10 and Linux.</div><div><br></div><div>I'm booting the full RSTS V7.0-07 disk, built by by Chuck Cranor. This boots fine, and I can log in on the simulated console. However, I can't persuade it to recognise any additional terminals. If I use:</div><div><br></div><div>set dli enable</div><div>set dli lines=8</div><div>attach dli 10001</div><div><br></div><div>Then I get a telnet server appearing on port 10001, which prints "Connected to the PDP-11 simulator DLI device, line 0" when I boot the RSTS system disk. However, there's no response to any input once RSTS is up and running.  I've also tried using a DZ11</div><div><br></div><div>set dz lines=8</div><div>attach dz 10002</div><div><br></div><div>and in that case I don't even get the "Connected...." line from simh. RSTS can apparently see the hardware though:</div><div><br></div><div>RSTS V7.0-07 llama (DL0)<br><br><br>Option: HA<br><br>  HARDWR suboption? LI<br><br>  Name  Address Vector  Comments<br>  TT:    177560   060<br>  RK:    177400   220   RK05F units: none<br>  RL:    174400   160   Units: 0(RL01) 1(RL01) 2(RL01) 3(RL01)<br>  RM:    177440   210   Units: 0(RK06) 1(RK06) 2(RK06) 3(RK06) 4(RK06)<br>                               5(RK06) 6(RK06) 7(RK06)<br>  RR:    176700   254   BAE=+050, Units: 0(RM03) 1(RM03) 2(RM03)<br>                               3(RM03) 4(RM03) 5(RM03) 6(RM03) 7(RM03)<br>  TM:    172520   224<br>  PR0:   177550   070<br>  PP0:   177554   074<br>  LP0:   177514   200<br>  RX0:   177170   264<br>  KL0:   176500   300<br>  KL1:   176510   310<br>  KL2:   176520   320<br>  KL3:   176530   330<br>  KL4:   176540   340<br>  KL5:   176550   350<br>  KL6:   176560   360<br>  KL7:   176570   370<br>  DZ0:   160100   400<br>  DZ1:   160110   410<br><br>  KW11L  177546   100<br>  SR     177570<br>  DR     177570<br><br>  Hertz = 60.<br><br>  Other: FPU, SL, 22-Bit Addressing, Cache w/address, System ID = 4660<br></div><div><br></div><div>If I boot an RSX-11M disk, then additional terminal interfaces seem to work fine, so the problem seems specific to RSTS.   I saw references in the list archive to other pre-built systems on <a href="http://www.rsts.org">www.rsts.org</a> but that doesn't seem to be available at the moment, so I can't try another build right now.</div><div><br></div><div>Any clues on what I'm missing ?  <br></div><div><br></div><div>Thanks,</div><div>Trevor</div><div><br></div><div><br></div></div>