<div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div>I'm trying to get the isys80x0 series to use the floppy disk controllers, but no matter what I try to do in the SCP as far as enabling or disabling the SBC20x or ZX200A, the mon80 (a or b) always says "No Disk Controller Present" when I issue the FB command.</div><div><br></div><div>I'm probably missing something like a port output command, or a complie time setting, or something.</div><div><br></div><div>When I start the emulator I get:</div><div><br></div><div>-----------------</div><div>$ isys8010<br>Initializing iSBC-80/10 SBC<br>   Onboard Devices:<br>   8080: Reset<br>      8251-0: Hardware Reset<br>      8251-0: Registered at 00EC<br>         Port 00EC is assigned to dev 0000<br>         Port 00ED is assigned to dev 0000<br>      8251-0: Software Reset<br>      8255-0: Reset<br>      8255-0: Registered at 00E4<br>         Port 00E4 is assigned to dev 0000<br>         Port 00E5 is assigned to dev 0000<br>         Port 00E6 is assigned to dev 0000<br>         Port 00E7 is assigned to dev 0000<br>      8255-1: Reset<br>      8255-1: Registered at 00E8<br>         Port 00E8 is assigned to dev 0001<br>         Port 00E9 is assigned to dev 0001<br>         Port 00EA is assigned to dev 0001<br>         Port 00EB is assigned to dev 0001<br>      EPROM: Configured, Not attached<br>   Multibus: Reset<br>      iSBC-201 FDC Board - Not Found<br>      iSBC-202 FDC Board - Found<br>         isbc202-0: Hardware Reset<br>         isbc202-0: Registered at 0078<br>         Port 0078 is assigned to dev 0000<br>         Port 0079 is assigned to dev 0000<br>         Port 007A is assigned to dev 0000<br>         Port 007B is assigned to dev 0000<br>         Port 007F is assigned to dev 0000<br>         isbc202-0: Software Reset<br>         SBC2020: Configured, Status=19 Attached to (null)<br>         SBC2021: Configured, Status=1B Attached to (null)<br>         SBC2022: Configured, Status=3B Attached to (null)<br>         SBC2023: Configured, Status=7B Attached to (null)<br>         isbc202-0: Software Reset<br>         SBC2020: Configured, Status=19 Attached to (null)<br>         SBC2021: Configured, Status=1B Attached to (null)<br>         SBC2022: Configured, Status=3B Attached to (null)<br>         SBC2023: Configured, Status=7B Attached to (null)<br>      ZX-200A FDC Board - Not Found<br><br>Intel System 80/10 simulator V4.0-0 Current        git commit id: 584147fb<br>sim> <br></div><div>-----------------------------------</div><div>But devices are all disabled:</div><div>-----------------------------------</div><div>sim> sh de<br>Intel System 80/10 simulator configuration<br><br>I8080<br>EPROM<br>RAM<br>I8251<br>I8255    2 units<br>MBIRQ<br>SBC064    disabled<br>SBC201    disabled<br>SBC202    disabled<br>ZX200A    disabled<br>sim> </div><div>---------------------------------------------------</div><div><br></div><div>and if I enable or disable any of the 3 devices and issue a reset command, I get the same output as the initial status display, nothing changes.</div><div><br></div><div>what am I doing wrong?<br><br></div><div>I'm trying to use Bill Beech's config files, disk images and rom images to boot CP/M on these devices but I can't find any documentation that will clear up any of the issues I am having.</div><div><br></div><div>Thanks for looking into this . . .<br></div></div></div></div></div>